PC Control Tensile Tester Machine , Fiber Tester SUS304 Benchtop Tensile Tester

 
Fiber Tester PC Control Photoelectric sensors Fiber Tensile Strength Tester
 
 
Application
 
Fiber Tester PC Control Photoelectric sensors Fiber Tensile Strength Tester is mainly used a variety of stretch fiber ( Carbon fiber cloth, carbon fiber cloth, carbon cloth, carbon fiber fabric, carbon fiber tape, carbon fiber sheet )material products, tensile strength test,peel, tear, anti-physical properties of shear. While testing and data processing in accordance with various standards GB, ISO, JIS, ASTM, DIN, and user-supplied
 

Main features

Leather Tensile Digital Display Servo Frequency Conversion Tensile Strength Tester using import photoelectric encoder, controller based on embedded single chip microcomputer architecture, built-in powerful control software, measurement, control, and computing, storage in one. Has automatically calculation stress, and extends rate (needed added distribution introduction stretch meter), and tensile strength, and modulus of function, automatically statistics results; automatically records maximum points, and fracture points, and specified points of force value or elongation volume; used computer for test process and the test curve of dynamic displayed, and for data processing, test end Hou can through graphics processing module on curve zoom for data again analysis edit, and can print report, products performance reached international advanced level.
 
 Measuring principle
1, measurement of tensile testing machine is the result of force sensors, amplifiers and data disposition system measurement. Learned from information mechanics, small deformation under strain to an elastic element ε with elastic element is directly proportional to the force, and elastic form in proportion. A case study of s-type testing machine sensor if the sensor was pulling effect of p, because elastic element looks pasted strain, due to the strain of elastic element is proportional to the size of the force p, it will strain gage circuit for measuring access, after measuring the output voltage, and measure the size of the force.
 

2 after deformation, deformation measurements measurement Setup to measure, it is used for measuring specimen deformation occurred in the experiment process. The installation there are two Chuck on, through the idea of a biography structure and mounted on top of the measuring installation of optical encoders connected together, when intervals between two Chuck change, drive the torsion of photoelectric encoder, encoder will have a pulse signal output. By the Manager for the disposition of this signal, the deformation of the sample can be drawn.
 

3, beam displacement measure the deformation measurement of truth with much the same thing, is the number of measurements of optical encoder output pulse to get the displacement of the beam.
 
 
structure

Fiber tensile testing machine adopts single-arm structure, the host portion of the column, on the beam, the beam, the composition of the table, speed control system installed in the lower part of the table, by the governor and high precision, wide range, stable performance servo motor through synchronous toothed belt deceleration system driven ball screw rotates, the ball screw drive beam to drive accompanied by stretching (or compression, bending accompanied) to move up and down, to achieve loading and unloading samples. The structure has a high stiffness, high efficiency, stable transmission and so on.

Technical Parameters
 

The speed tests

Some equipment market in 10 ~ 500 mm / min, and some in the 0.001 ~ 500 mm / min, the former general use of common control system, low cost, rough affect the accuracy; which uses servo system, expensive, high precision, for flexible packaging business, the choice of servo system, speed range 1 ~ 500mm / min is sufficient, this will not affect the accuracy of prices within a reasonable range.

Buy Considerations

1, should first consider the need to test the material tensile range.
2, the test stroke problems.
3, the standard configuration issues.
4, the output results.
5, do a pilot project on.
6, the main mechanical configuration
7, test speed.
8, the measurement accuracy.

Our company

Introduction:

Strength Factory Management

Modern equipment and superb process production including laser cutting panels and wood, ERP systems, production control systems, cutting automation, our advanced equipment can help us reduce waste ...

Senior Original design Team
4 Research and production base, more than 10 doctoral advisor, more than 10 High-tech products, more than 50 product patents ...

Exquisite technology, testing agency Quality Control Factory Direct Sales
Focus on product quality, independent quality inspection departments to strictly check each process of inspection and pay attention to customer service, program creative design and later process production, product quality and quantity ...

Sturdy package turn, professional installation, global distribution
With the national well-known global Express company to ensure the quality of the goods during the freight and freight time ...

Environmental certification Quality raw materials
Set up a perfect ISO9001 quality assurance system, adhere to the "standard process operation, using the right data to speak" principle of total quality management, the quality of physical assessment standards to "customer expectations"

and ...